Thickness Dependency of CuO Nanocoating Layer on Thermal Performance of HPHE

Aysar Abd Alrazaq Alamery; Hussein Ali Jawad; Zainab Fadhil Mahdi

doi:doi:10.11648/j.ijmsa.20140306.16

| Peer-Reviewed

Thickness Dependency of CuO Nanocoating Layer on Thermal Performance of HPHE

Aysar Abd Alrazaq Alamery, Hussein Ali Jawad, Zainab Fadhil Mahdi

Published in International Journal of Materials Science and Applications (Volume 3, Issue 6)

Received: 8 July 2014 Accepted: 24 July 2014 Published: 20 October 2014

Views: Downloads:

Download PDF

Share This Article

Twitter
Linked In
Facebook

Abstract

Among the different passive techniques present, surface coating seems to the most effective one. Copper oxide-based materials are of interest on account of their potential uses in many technological fields. Modeling of the nanocoating on fins in Thermosyphon heat exchangers using ANSYS software is introduced. The temperature distribution was investigated. Seven thicknesses of CuO coating layers are used on fins of HPHE with the aim of improving working system. The enhancement is proportioning with the increment in coat thickness at the evaporator section of transient conditions (-16.95, 3.12, 30.66, 52.68, 70.65, 85.55and 98.09) for (10, 25, 50, 75, 100,125and150 µm) thicknesses respectively. From these results, maximum enhancement occurred at150 µm coat. Coat process of the evaporator fins can give fast response of nanofluid to absorb the latent heat from the outdoor air and vaporize to start the closed cycle working system so the increasing in the energy saving is investigated.

Published in	International Journal of Materials Science and Applications (Volume 3, Issue 6)
DOI	10.11648/j.ijmsa.20140306.16
Page(s)	314-320
Creative Commons	This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.
Copyright	Copyright © The Author(s), 2014. Published by Science Publishing Group

Keywords

HVAC, HPHE, ANSYS, Coating Layer Thickness, Copper Oxide, Temperature Distribution

References

[1]	H. Mirshahi, M. Rahimi,"Experimental Study on the Effect of Heat Loads, Fill Ratio and Extra Volume on Performance of a Partial-Vacuumed Thermosyphon",Iranian Journal of Chemical Engineering ,Vol. 6, No. 4 (Autumn), 2009, IAChE.
[2]	E. Firouzfar, M. Soltanieh, S. H. Noie,M. H. Saidi,"Investigation of heat pipe heat exchanger effectiveness and energy saving in air conditioning systems using silver nanofluid",Int. J. Environ. Sci. Technol., 2012, 9:587–594.
[3]	S. Kumar C. S, S. Suresh and Rajiv K,"Heat Transfer Enhancement by Nano StructuredCarbon Nanotube Coating", International Journal of Scientific & Engineering Research Volume 3, Issue 6,June-2012, ISSN 2229-5518.
[4]	A. Khare,A. Paul andG. Selokar,"Design Development of Test-Rig to Evaluate Performance of Heat Pipes in Cooling of PrintedCircuit Boards",VSRD-MAP, Vol. 1 (2), 2011, 65-79.
[5]	M. Shafahi, V. Bianco,K. Vafai and O. Manca,"Thermal performance of flat-shaped heat pipes using nanofluids",International Journal of Heat and Mass Transfer 53 ,2010, 1438–1445.
[6]	H.A. Mohammed and K. Narrein,"Thermal and hydraulic characteristics of nanofluidflow in a helically coiled tube heat exchanger",International Communications in Heat and Mass Transfer 39 2012, 1375–1383.
[7]	P.G. Anjankar and R.B.Yarasu,"Experimental Analysis of Condenser Length Effect on thePerformance of Thermosyphon", International Journal of Emerging Technology and Advanced Engineering, Volume 2, Issue 3, March 2012, ISSN 2250-2459.
[8]	W. Srimuang1,P.Khantikomol and P. Amtachaya," Two Phase Closed Thermosyphon (TPCT) andit’sapplication for an Air-to-air Heat Exchanger", The Journal of KMUTNB., Vol. 22, No. 1, Jan. - Apr. 2012.
[9]	A. A. Alamery, H. A. Jawad, H. A. Ameen and Z.F. Mahdi," Effect of Hard Materials Nanocoating on Fins in (Thermosyphon) HPHE with Nano Working Fluid",IJERT , Volume. 3, Issue. 06, June – 2014.
[10]	S.H. Noie, S. ZeinaliHeris, M. Kahani and S.M. Nowee," Heat transfer enhancement using Al2O3/water nanofluid in a two-phase closed Thermosyphon ", International Journal of Heat and Fluid Flow 30, 2009, pp.700–705.
[11]	Y.H. Yau," Experimental thermal performance study of an inclined heat pipe heat exchanger operating in high humid tropical HVAC systems", International Journal of Refrigeration 30 ,2007, 1143-1152.
[12]	J. H.Lienhard IV and J.H.Lienhard V,”A heat transfer textbook”, Third edition, 2001.

Cite This Article

Plain Text BibTeX RIS

APA Style

Aysar Abd Alrazaq Alamery, Hussein Ali Jawad, Zainab Fadhil Mahdi. (2014). Thickness Dependency of CuO Nanocoating Layer on Thermal Performance of HPHE. International Journal of Materials Science and Applications, 3(6), 314-320. https://doi.org/10.11648/j.ijmsa.20140306.16

Copy | Download

ACS Style

Aysar Abd Alrazaq Alamery; Hussein Ali Jawad; Zainab Fadhil Mahdi. Thickness Dependency of CuO Nanocoating Layer on Thermal Performance of HPHE. Int. J. Mater. Sci. Appl. 2014, 3(6), 314-320. doi: 10.11648/j.ijmsa.20140306.16

Copy | Download

AMA Style

Aysar Abd Alrazaq Alamery, Hussein Ali Jawad, Zainab Fadhil Mahdi. Thickness Dependency of CuO Nanocoating Layer on Thermal Performance of HPHE. Int J Mater Sci Appl. 2014;3(6):314-320. doi: 10.11648/j.ijmsa.20140306.16

Copy | Download

@article{10.11648/j.ijmsa.20140306.16,
  author = {Aysar Abd Alrazaq Alamery and Hussein Ali Jawad and Zainab Fadhil Mahdi},
  title = {Thickness Dependency of CuO Nanocoating Layer on Thermal Performance of HPHE},
  journal = {International Journal of Materials Science and Applications},
  volume = {3},
  number = {6},
  pages = {314-320},
  doi = {10.11648/j.ijmsa.20140306.16},
  url = {https://doi.org/10.11648/j.ijmsa.20140306.16},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ijmsa.20140306.16},
  abstract = {Among the different passive techniques present, surface coating seems to the most effective one. Copper oxide-based materials are of interest on account of their potential uses in many technological fields. Modeling of the nanocoating on fins in Thermosyphon heat exchangers using ANSYS software is introduced. The temperature distribution was investigated. Seven thicknesses of CuO coating layers are used on fins of HPHE with the aim of improving working system. The enhancement is proportioning with the increment in coat thickness at the evaporator section of transient conditions (-16.95, 3.12, 30.66, 52.68, 70.65, 85.55and 98.09) for (10, 25, 50, 75, 100,125and150 µm) thicknesses respectively. From these results, maximum enhancement occurred at150 µm coat. Coat process of the evaporator fins can give fast response of nanofluid to absorb the latent heat from the outdoor air and  vaporize to start the closed cycle working system  so the increasing in the energy saving is investigated.},
 year = {2014}
}

Copy | Download

TY  - JOUR
T1  - Thickness Dependency of CuO Nanocoating Layer on Thermal Performance of HPHE
AU  - Aysar Abd Alrazaq Alamery
AU  - Hussein Ali Jawad
AU  - Zainab Fadhil Mahdi
Y1  - 2014/10/20
PY  - 2014
N1  - https://doi.org/10.11648/j.ijmsa.20140306.16
DO  - 10.11648/j.ijmsa.20140306.16
T2  - International Journal of Materials Science and Applications
JF  - International Journal of Materials Science and Applications
JO  - International Journal of Materials Science and Applications
SP  - 314
EP  - 320
PB  - Science Publishing Group
SN  - 2327-2643
UR  - https://doi.org/10.11648/j.ijmsa.20140306.16
AB  - Among the different passive techniques present, surface coating seems to the most effective one. Copper oxide-based materials are of interest on account of their potential uses in many technological fields. Modeling of the nanocoating on fins in Thermosyphon heat exchangers using ANSYS software is introduced. The temperature distribution was investigated. Seven thicknesses of CuO coating layers are used on fins of HPHE with the aim of improving working system. The enhancement is proportioning with the increment in coat thickness at the evaporator section of transient conditions (-16.95, 3.12, 30.66, 52.68, 70.65, 85.55and 98.09) for (10, 25, 50, 75, 100,125and150 µm) thicknesses respectively. From these results, maximum enhancement occurred at150 µm coat. Coat process of the evaporator fins can give fast response of nanofluid to absorb the latent heat from the outdoor air and  vaporize to start the closed cycle working system  so the increasing in the energy saving is investigated.
VL  - 3
IS  - 6
ER  -

Copy | Download

Author Information

Aysar Abd Alrazaq Alamery

Institute of Laser for Postgraduate Studies, University of Baghdad, Jadriha, P. O. Box 47314 Baghdad, Iraq
Hussein Ali Jawad

Institute of Laser for Postgraduate Studies, University of Baghdad, Jadriha, P. O. Box 47314 Baghdad, Iraq
Zainab Fadhil Mahdi

Institute of Laser for Postgraduate Studies, University of Baghdad, Jadriha, P. O. Box 47314 Baghdad, Iraq

Download PDF

Sections

Plain Text BibTeX RIS

APA Style

Aysar Abd Alrazaq Alamery, Hussein Ali Jawad, Zainab Fadhil Mahdi. (2014). Thickness Dependency of CuO Nanocoating Layer on Thermal Performance of HPHE. International Journal of Materials Science and Applications, 3(6), 314-320. https://doi.org/10.11648/j.ijmsa.20140306.16

Copy | Download

ACS Style

Aysar Abd Alrazaq Alamery; Hussein Ali Jawad; Zainab Fadhil Mahdi. Thickness Dependency of CuO Nanocoating Layer on Thermal Performance of HPHE. Int. J. Mater. Sci. Appl. 2014, 3(6), 314-320. doi: 10.11648/j.ijmsa.20140306.16

Copy | Download

AMA Style

Aysar Abd Alrazaq Alamery, Hussein Ali Jawad, Zainab Fadhil Mahdi. Thickness Dependency of CuO Nanocoating Layer on Thermal Performance of HPHE. Int J Mater Sci Appl. 2014;3(6):314-320. doi: 10.11648/j.ijmsa.20140306.16

Copy | Download

@article{10.11648/j.ijmsa.20140306.16,
  author = {Aysar Abd Alrazaq Alamery and Hussein Ali Jawad and Zainab Fadhil Mahdi},
  title = {Thickness Dependency of CuO Nanocoating Layer on Thermal Performance of HPHE},
  journal = {International Journal of Materials Science and Applications},
  volume = {3},
  number = {6},
  pages = {314-320},
  doi = {10.11648/j.ijmsa.20140306.16},
  url = {https://doi.org/10.11648/j.ijmsa.20140306.16},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ijmsa.20140306.16},
  abstract = {Among the different passive techniques present, surface coating seems to the most effective one. Copper oxide-based materials are of interest on account of their potential uses in many technological fields. Modeling of the nanocoating on fins in Thermosyphon heat exchangers using ANSYS software is introduced. The temperature distribution was investigated. Seven thicknesses of CuO coating layers are used on fins of HPHE with the aim of improving working system. The enhancement is proportioning with the increment in coat thickness at the evaporator section of transient conditions (-16.95, 3.12, 30.66, 52.68, 70.65, 85.55and 98.09) for (10, 25, 50, 75, 100,125and150 µm) thicknesses respectively. From these results, maximum enhancement occurred at150 µm coat. Coat process of the evaporator fins can give fast response of nanofluid to absorb the latent heat from the outdoor air and  vaporize to start the closed cycle working system  so the increasing in the energy saving is investigated.},
 year = {2014}
}

Copy | Download

TY  - JOUR
T1  - Thickness Dependency of CuO Nanocoating Layer on Thermal Performance of HPHE
AU  - Aysar Abd Alrazaq Alamery
AU  - Hussein Ali Jawad
AU  - Zainab Fadhil Mahdi
Y1  - 2014/10/20
PY  - 2014
N1  - https://doi.org/10.11648/j.ijmsa.20140306.16
DO  - 10.11648/j.ijmsa.20140306.16
T2  - International Journal of Materials Science and Applications
JF  - International Journal of Materials Science and Applications
JO  - International Journal of Materials Science and Applications
SP  - 314
EP  - 320
PB  - Science Publishing Group
SN  - 2327-2643
UR  - https://doi.org/10.11648/j.ijmsa.20140306.16
AB  - Among the different passive techniques present, surface coating seems to the most effective one. Copper oxide-based materials are of interest on account of their potential uses in many technological fields. Modeling of the nanocoating on fins in Thermosyphon heat exchangers using ANSYS software is introduced. The temperature distribution was investigated. Seven thicknesses of CuO coating layers are used on fins of HPHE with the aim of improving working system. The enhancement is proportioning with the increment in coat thickness at the evaporator section of transient conditions (-16.95, 3.12, 30.66, 52.68, 70.65, 85.55and 98.09) for (10, 25, 50, 75, 100,125and150 µm) thicknesses respectively. From these results, maximum enhancement occurred at150 µm coat. Coat process of the evaporator fins can give fast response of nanofluid to absorb the latent heat from the outdoor air and  vaporize to start the closed cycle working system  so the increasing in the energy saving is investigated.
VL  - 3
IS  - 6
ER  -

Copy | Download